<div dir="ltr">Dear Mufeeda,<br><br>The lifespan of a LaB6 gun depends on several critical factors, including (1) vacuum level, (2) oversaturation, and (3) mechanical stresses. In a conventional TEM setup where a nearly parallel electron beam is employed (not STEM), it is recommended to operate with a filament current level that's one or two steps below the saturation limit. Exceeding this saturation point can lead to adverse consequences as the tip begins to deplete its lanthanum content, subsequently causing an increase in work function. To counteract this increase, users may raise the filament current, further accelerating tip depletion. Moreover, maintaining a low vacuum level can introduce contamination, and in severe cases, trigger arcing, both of which can harm the tip.<br><br>Earöy determination of the end of the LaB6 gun's operational life can be somewhat complex. If the gun is correctly installed and perfectly aligned, any abnormal emission patterns, such as deviations from the classic four-fold emission shape with a central peak or significantly reduced beam current, can be indicative of an approaching end. It's essential to note that blinking, in itself, doesn't necessarily signal the end of the gun's life; it could be attributed to issues in the high-tension tank, gun head, cable, or even suboptimal vacuum conditions. Contaminants in the wehnelt cup, objective pole piece or within other parts of the column can also induce such effects. While arcing is less likely to occur at 120 kV, it's still crucial to verify the vacuum level and monitor emission current fluctuations. If issues persist, it's advisable to consult your service contract provider.<br><br>Please be aware that my direct experience with LaB6 TEMs is limited to an older Philips CM200, and I haven't worked with a Talos 120 kV. However, as a general guideline, the typical lifespan of a LaB6 gun under continuous operation is approximately six months. Factors like suboptimal vacuum levels, arcing, frequent thermal cycling (number of turning on and off), and oversaturation (excessive filament current) can shorten this lifespan due to thermal stresses and contamination buildup.<br><br>Best Regards,<br><div><br></div><div>Farzad Hamdi</div><div><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div style="color:rgb(0,0,0)"><div dir="auto" style="color:rgb(34,34,34)">Kastritis Laboratory for Biomolecular Research</div><div dir="auto" style="color:rgb(34,34,34)">Institute of Biochemistry and Biotechnology, Biocenter, </div><div dir="auto" style="color:rgb(34,34,34)">Martin Luther University Halle-Wittenberg, Halle (Saale), Germany</div><div dir="auto" style="color:rgb(34,34,34)">----------------------------------------------------------------------------------------</div><div dir="auto" style="color:rgb(34,34,34)">Biozentrum, Room A.2.14 & 15</div><div dir="auto" style="color:rgb(34,34,34)">Weinbergweg 22, 06120 Halle</div><div dir="auto" style="color:rgb(34,34,34)">Telefone:</div><div dir="auto" style="color:rgb(34,34,34)">Cellphone: +49 176 56881282</div><div dir="auto" style="color:rgb(34,34,34)">Office: +49 345 5524984</div><div dir="auto" style="color:rgb(34,34,34)">Glacios Room: +49 345 5524883</div><div dir="auto" style="color:rgb(34,34,34)">JEM-3200FSC Room: +49 345 5524868</div><div dir="auto" style="color:rgb(34,34,34)">Web (Lab): <a href="https://urldefense.com/v3/__https://blogs.urz.uni-halle.de/kastritislab/__;!!Mih3wA!EeeOM1kQFRpqNiy2UNzpEj3g3GDAdhPHEJpnqLoxvFiQ72wpwCwxr5Pdn5LrrMyu0wwXz85QbAk_K0ehLw$" style="color:rgb(17,85,204)" target="_blank">https://blogs.urz.uni-halle.de/kastritislab/</a></div></div></div></div></div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Oct 11, 2023 at 8:19 AM Mufeeda C M <<a href="mailto:mufeeda.01@gmail.com">mufeeda.01@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><font face="arial, sans-serif">Dear 3D EM members,</font><div><font face="arial, sans-serif"><br></font></div><div><p class="MsoNormal" style="text-align:justify;line-height:150%;margin:0cm 0cm 8pt"><font face="arial, sans-serif"><span style="background-image:initial;background-position:initial;background-size:initial;background-repeat:initial;background-origin:initial;background-clip:initial">We have
Talos L120C, recently we noticed that the beam is quite unstable (it kind of
started flickering)</span>. Filament readout shows 830+ hrs.
Should we replace the filament sooner? </font></p><p class="MsoNormal" style="text-align:justify;line-height:150%;margin:0cm 0cm 8pt"><font face="arial, sans-serif">Is there any disadvantage if we set the filament heating upto 50? </font></p>

<br><div><img src="cid:ii_lnlcqevk0" alt="image.png" width="542" height="407"><br></div><div><br></div><span class="gmail_signature_prefix">--</span></div><div><br></div><div><span class="gmail_signature_prefix"></span>Thanks & Regards<div dir="ltr" class="gmail_signature">Mufeeda Madathummal</div></div></div>
_______________________________________________<br>
3dem mailing list<br>
<a href="mailto:3dem@ncmir.ucsd.edu" target="_blank">3dem@ncmir.ucsd.edu</a><br>
<a href="https://mail.ncmir.ucsd.edu/mailman/listinfo/3dem" rel="noreferrer" target="_blank">https://mail.ncmir.ucsd.edu/mailman/listinfo/3dem</a><br>
</blockquote></div>